Home and Garden

Refine Search

What are some guidelines for installing ledgestone veneer?

Create the initial moisture barrier by nailing felt or a waterproof house-wrapping material like DuPont's Tyvek to the wooden exterior wall. If you are applying the veneer over an existing brick or concrete wall, the moisture barrier is not necessary. Attach the lath to the wall using nails or screws with plastic washers to seal out moisture.\nApply the mortar in a single layer between one-sixteenth and one-eighth of an inch thick. Absolute precision is not necessary, but try to make the mortar layer relatively even.\nOnce the mortar is on the lath, attach the ledgestone veneer flats to t..

Continue Reading

How do you grow Dianthus perennial flowers?

Select a good locationSelect a location in which to plant the dianthus that receives full sun. The soil needs to be well-drained with a neutral pH.Prepare the soilTill the top 12 inches of the soil to loosen it, and work in 2 to 4 inches of compost.Plant the dianthusDig a hole that is twice the size of the container or root ball of the plant that is between 6 and 12 inches away from other plants. Place the plant in the hole, and fill it in with the soil. Gently tamp down the dirt. Water the plantWater the plant immediately after planting. Make sure it gets 1 inch of moisture per week.Mulch and..

Continue Reading

How do you take care of peach trees?

After planting a peach tree, spread a 3-inch deep layer of organic mulch around the tree to keep the soil moist, and water it often using drip irrigation or a method that waters the tree slowly and deeply. Make sure the soil stays moist, but not overly damp or soggy, which can cause root rot.\nFeed the tree a high-nitrogen fertilizer six weeks after planting and every month afterwards, and feed it twice during the growing season the next year. In following years, only fertilize the tree once per growing season. If the tree doesn't grow at least 10 inches per year, increase feedings. In th..

Continue Reading

How do you stain a concrete floor?

Clean the concrete floorRemove all furnishings, and sweep the floor well. Mop the floor with plain water, changing the water frequently to keep it clean.Apply an etching solutionEvenly spread a concrete etching solution over the floor with a push broom. Give the solution 15 minutes to soak into the floor.Scrub the floor with a stiff brushScrub the entire floor vigorously to deep clean it and help open the pores.Mop with waterMop up the etching solution along with any scrubbed-up dirt. Use plain water, and change it frequently.Let the floor dryWait until the floor has completely air dried.Fill ..

Continue Reading

What is the best way to clean grout?

Apply stain remover, and scub the groutProtect your hands with rubber gloves, and saturate the grout with mildew remover. Be sure to use a cleaner that is designed to remove mildew. Use a grout brush to scrub the grout in the grout direction, and let the cleaner set for 15 minutes.Rinse the groutSoak a sponge with clean water, and use the sponge to rinse the surface in order to remove all the dirt and cleaner residue. When rinsing, scrub away any remaining stains with a grout brush. Repeat the process as needed until all the dirt disappears, and allow the surface to dry.Protect the grout from ..

Continue Reading

What is Timbermill log siding made of?

Timbermill's log vinyl siding is made using chlorinated polyvinyl chloride, orCPVC, with a backing of polystyrene foam to strengthen the vinyl and provide insulation as well. Chlorinated polyvinyl chloride is a little stronger than regular polyvinyl chloride, orPVC. It withstands a wider range of temperatures without failing.Available in forest brown or American cedar colors, Timbermill's log vinyl siding doesn't require painting, staining or sealing like real wood. Ownerssimply need to inspect it visually every year and wash it when itis dirty. Timbermill also offers a limited ..

Continue Reading

How do you replace the resistor on an air conditioner blower fan?

Start by locating the blower motor and resistor. To do this, check around the motor for a 2- by 3-inch plate usually held in place by either two or four screws. To ascertain that the resistor is faulty and needs replacement, test it by turning the fan control to all positions to check the speeds, taking note of the speeds that work and those that fail to work. A faultless resistor enables the fan to work on all the speeds.\nIf the fan speeds fail to work, check the heating, ventilating and air conditioning system fuse. Remove a faultless fuse, turn on the ignition key, and check if the volts r..

Continue Reading

What is laser cutting?

Laser cutters are used to create highly precise parts with tolerances measured in thousandths of an inch. Laser cutting uses light to heat a material to its melting point. An assist gas such as air or nitrogen is used to keep the material immediately surrounding the cutting area cool. Industrial cutting lasers are capable of accurately cutting any non-reflective metal. Material can range from 22-gauge steel up to 2-inch thick steel plate.

Continue Reading

What should you look for when buying a vintage coffee grinder?

When shopping for a burr grinder, beware of false ones. An original burr coffee grinder should have sharp opposing cutting surfaces. If on a tight budget but still want a burr grinder, go for a conical burr grinder that is slightly cheaper. An original burr coffee grinder should either be ceramic or stainless steel and should have efficient power from the accompanying motor.

Continue Reading

How do you change the drill bit in a Black & Decker Pivot Plus?

In order to insert the drill bit:Install new drill bit into the drillHold the rear part of the drill chuck in one hand and with the other hand, rotate the front half in a counterclockwise direction. Insert the drill bit fully into the chuck.Secure the drill bitTighten and secure the bit by holding the rear of the chuck and rotate the front half in a clockwise direction.

Continue Reading
Showing 2721 to 2730 of 10000 (1000 Pages)