Vehicles

Refine Search

How do you adjust your automotive headlights?

When parking the car in front a blank wall for adjusting its headlights, leave adequate walking space between the vehicle and the wall. After switching on the headlights to Low, measure the distance between the ground and the headlamp center using a measuring tape. Mark the points on the wall, and connect them through a horizontal line.\nSet the low beam so that it is emitted in a straight line from the lamps and its center falls at the center of the horizontal line. Turn the adjustment screws on the top and sides of the headlamp to adjust the beam upwards or downwards and towards right or lef..

Continue Reading

What is E85 gasoline?

Not all gas stations have pumps for E85 fuel. The pumps are clearly marked to avoid confusion with other fuel types. E85 fuel is often cheaper than lower ethanol fuels, but the vehicle gets lower gas mileage when running on E85. This is because the higher ethanol blends have less energy based on volume than gasoline.

Continue Reading

Where can you find resources for the MVA driving test?

The MVA states that approximately 50 percent of test takers fail the knowledge portion of the driving test, so it is important to use both the driver's manual and the tutorials that the MVA offers as resources. The resources made available by the MVA are the only ones that should be trusted when studying for the MVA driving test.

Continue Reading

What is an NGK gap chart?

For nearly all of the spark plugs that NGK manufactures, the spark plug gap is controlled only during the manufacturing process and is not adjustable by the spark plug's owner. However, certain spark plugs do have an adjustable plug gap for special applications. This is necessary for vehicles with high compression or a high fuel-to-air ratio. These vehicles require a greater voltage to ignite the fuel and therefore need a smaller spark plug gap.

Continue Reading

How do you fix a cylinder misfire?

Determine the problem locationAttach the scan tool to the OBDII port to retrieve the diagnostic code. A P0200 series code generally indicates a problem with a fuel injector, while a P0300 series code indicates another issue, often with the spark plug or wire. If the code replaces the final zero in either of these codes with another number, it indicates the cylinder where the problem is occurring. If the code has a zero as the final digit, the problem is affecting two or more cylinders. Using the scan tool prevents damage to the electronics caused by the older method of removing plug wires one ..

Continue Reading

How do you do a three-point turn?

Pull over to the right curbBefore starting the three-point turn, pull your car over to the right curb. Try to get your car as close to the curb as possible. A distance of 6 to 10 inches is preferable.Complete the first turnTurn on your left blinker. Turn your steering wheel as far to the left as possible. Make sure there is no traffic coming, then drive forward until you are 6 to 10 inches from the opposite curb. The car should be close to perpendicular to the opposite curb.Make the second turnLook to make sure there is no traffic coming from either way. Turn on your right turn signal, and tur..

Continue Reading

What are some common parts sold by Tom's Bronco Parts?

Tom's Bronco Parts also lists parts for Bronco suspensions and engines, as well as most of the accessories associated with them. The types of Bronco parts available are sorted into two categories that differentiate between the ages of the Bronco. The first category is for Broncos made from 1966 to 1977. Broncos made from 1978 to 1996 are in another category. Finally, a third category exists for Ford trucks manufactured between 1948 and 1996.

Continue Reading

How do you use a steering wheel puller?

Disconnect the battery groundDisconnect the ground lead from the battery before beginning any work.Remove the airbagLoosen the screws from the back of the steering wheel. Lift the entire airbag unit from the steering wheel, and disconnect any wires. Store the unit in a safe place where static electricity does not cause it to expand.\n\n\nRemove the retaining nutUse a wrench to loosen and remove the retaining nut that holds the steering wheel in place. Set the nut aside in a safe place.Attach the wheel pullerDetermine the appropriate bolt size needed to attach the puller to the steering wheel. ..

Continue Reading

How do you replace an air filter?

Take the air cleaner lid offCheck your owner's manual to see the location of the air cleaner in your engine; it generally is a rectangular container on one side of the engine compartment with a large duct going into it, or a large round container in the center. Remove any clips or other fasteners on the air cleaner and set to one side before taking the lid off.Check out the filterPull the old filter out; access should be easy after you take the lid off. Hold the old air filter up to the light; if it is opaque, or the residue on the air filter is dark gray or black, it's time for a ne..

Continue Reading

What are Caterpillar serial numbers?

The serial number starts with a three-digit prefix followed by a five-digit serial number. To find the model year of the Caterpillar equipment, locate the product identification number. The serial number of an engine is located on the right back side of the engine block. The serial number of a generator set is located on the left side of the generator. The serial number for a backhoe is located on the right side of the front frame near the pivot point.

Continue Reading
Showing 8731 to 8740 of 10000 (1000 Pages)